SB2040 Snowblower Assembly and Installation Assemble the Snowblower FOLLOW THESE INSTRUCTIONS CAREFULLY. Correct installation of this snowblower is es
Assembly and Installation SB2040 Snowblower I Install Push Frame to Subframe 1. Position the push frame to the subframe as shown. 2. Install two 1-5/1
SB2040 Snowblower Assembly and Installation Connect Lift Rods 1. Allow the subframe to pivot (while the blower head remains stationary), so you can co
Assembly and Installation SB2040 Snowblower Adjust Counterbalance Springs 1. Tighten the adjustment nut on each 75 mm (3.0 inches) counterbalance spr
SB2040 Snowblower Assembly and Installation Discharge Chute Assembly 1. Install the discharge guard on the chute as shown using two 3/8-3/4" hex
Assembly and Installation SB2040 Snowblower I Skid Shoe Installation 1. Insert one 5/16 x 1" carriage bolt into the lower hole of each skid shoe.
SB2040 Snowblower 5/16" HEX BOLT (4 5/16'' LOCK L-SHAPED BRACKET ON Install Brackets 1. If already installed, remove the hardware and t
SB2040 Snowblower 4. 5. 6. 7. 8. 9. 10. Slowly lift the subframe with the height adjustment lever, so the hole on the left side of the subframe aligns
1 SB2040 Snowblower is removed. 2. Make sure the PTO clutch lever is OFF. 3. Install the snowblower drive belt to the crankshaft pulley, then install
SB2040 Snowblower Check Belt Routing Path 1. Move the PTO clutch lever to ON. Verify the belt has been routed as shown. RIGHT SIDE ENGINE CRANKSHAFT P
SB2040 Snowblower The information in this operator’s manual is limited in application to the Honda SB2040 Snowblower (frame serial numbers 1000001 . 1
Adjust Belt Tension PIVOT PLATE ON 1. Locate the thin metal plate inside the U-SHAPED BRACKET tensioner spring. This plate is the belt tension indicat
SB2040 Snowblower Counterweight Installation 8 x 25 mm HEX BOLT (2) Install the rear counterweight bracket to the rear of the lawn tractor frame as sh
SB2040 Snowblower Safety Recomme
Safety Recommendations SB2040 Snowblower Before Operation 1. Before each use, clear work area of objects such as rocks, toys, wire, sleds, etc., which
SB2040 Snowblower Safety Recommendations 11. As a general rule, do not operate the machine in reverse. If it is absolutely necessary to back up: a) Di
Safety Recommendations SB2040 Snowblower Slope Operation 1. Slopes are a major factor in loss-of-control and tip-over accidents, which can result in s
SB32040 Snowblower Safety Recommendations Stopping 1. Before leaving operator’s position or leaving the machine unattended: a) Bring the lawn tractor
Safety Recommendations SB2040 Snowblower Controls Discharge Chute Rotation Crank Rotating this crank turns the discharge chute. Discharge Chute Deflec
SB2040 Snowblower Safety Recommendations Preparing for Snow Removal 0 Read the Safety Recommendations at the beginning of this section. 0 Park the law
Safety Recommendations SB2040 Snowblower Operating the Snowblower Read the lawn tractor owner's manual carefully. Be thoroughly familiar with the
1 SAFETY MESSAGES SB2040 Snowblower SAFETY MESSAGES Your safety and the safety of others are very important. We have provided important safety messag
SB2040 Snowblower Safety Recommendations You can be seriously injured by the fan or auger blades. The blades spin and can cut or amputate your hand or
Removing the Snowblower SB2040 Snowblower Removing the Snowblower 1. 2. 3. 4. Make sure the PTO clutch lever is OFF. Drive the lawn tractor to a flat,
SB2040 Snowblower Removing the Snowblower 7. Remove the 3.5 x 80 mm spring clip from the lockout pin, then engage the lockout pin into the push frame.
Removing the Snowblower SB2040 Snowblower 12. Lower the blower head slightly, then remove the four bolts that hold the u-shaped bracket to the subfram
SB2040 Snowblower Removing the Snowblower 15. Remove one spring clip from the counterweight retaining rod, then remove the rod. Remove the four suitca
Maintenance & Adjustments SB2040 Snowblower Maintenance & Adjustments Maintenance Schedule When Notes I Emte chains use chainsaw oil Every two
SB2040 Snowblower Maintenance & Adjustments Height Adjustment Lever Effort You may vary the amount of effort required to raise the blower head wit
I Maintenance & Adjustments SB2040 Snowblower Other Maintenance Items Shear bolt Replacement The auger and discharge fan both have special shear b
SB2040 Snowblower Maintenance & Adjustments Install the New Belt 1. Installation is the reverse of removal. Refer to the illustration here to ma
Parts Listing SB2040 Snowblower Parts Listing Blower Head & PTO Clutch Assembly 48 38 POP52152 (9610)
SB2040 Snowblower SAFETY MESSAGES THE IMPORTANCE OF INSTALLATION Proper installation is essential to operator safety and the reliability of the machin
SB2040 Snowblower Parts Listing Commercially Available Parts # Description Qty. 3 bolt, hex 318" nc x 4" 3 4 washer, lock 318" 5 5 n
Parts Listing SB2040 Snowblower Discharge Chute & Crank Rod 1 ‘22 40 POP 521 52 (961 0)
SB2040 Snowblower Parts Listing I Commercially Available Parts # Description Qty. 18 bolt, carriage 511 6" nc x 1-112" 2 19 bolt, hex 114&
Parts Listing SB2040 Snowblower Subframe I 42 POP 521 52 (961 0)
SB2040 Snowblower Parts Listing 90758-771 -SO0 Commercially Available Parts # Description Qty. # Description Qty. 44 bolt, hex 1/2" nc x 1-1/4&q
Optional Accessories SB2040 Snowblower Optional Accessories A number of optional accessories are available for use with the SB2040 Snowblower. See you
SB2040 Snowblower Warranty Service Information Warranty Service Information Honda Power Equipment dealership personnel are trained professionals. They
Current customer service contact information: United States, Puerto Rico, and U.S. Virgin Islands: Honda Power Equipment dealership personnel are tra
Safety Labels Immediately replace any label that becomes damaged or unreadable. Contact a servicing Honda lawn tractor dealer for replacement label. m
SB2040 Snowblower Assembly and Installation Ass
Assembly and Installation SB2040 Snowblower Inventory Hardware Bags Refer to the serial number (located on the right side of the blower head) and che
SB2040 Snowblower Assembly and Installation The following parts are included only with serial number 1000001 - 1000500only. The parts indicated in the
Assembly and Installation SB2040 Snowblower Hardware Measuring Chart How to measure hardware and components: INCHES 0 1 2 3 4 5 6 lT lr I I I I I I
Comments to this Manuals